Как изменить целевую температуру процессора на ноутбуке. Универсальной программы по изменению режима работы вентилятора ноутбуков нет. Для каждой марки есть свои приложения. Часто идут на родном диске с драйверами и приложения для изменения/контроля системных функций ноутбука. Asus EEE серии) 2. I8kfan. GUI (Dell Inspiron, Latitude, Precision) 3. Smart Fan (Acer Aspire One 4. Acer Aspire One серии) 5. TPFan. Control - (Lenovo Think. Pad серий X/T/R) 6. Acer Timeline 1. 41. Hardware Control Power. Profiles CPUMonitor (Acer Timeline. X 3. 82. 0) 8. Acer Aspire One (AA1) Fan Control (Acer Aspire One) 9. ACFan. Control (Acer Aspire 5. Lenovo S1. 0 Fan Control 1. HP Notebook Fan Control in HWi. NFO3. 2 (HP 8. 74. Кроме этого, присутствует возможность регулировки оборотов вентиляторов, таким образом понижать шум, используя утилиту Notebook FAN Control. Работает на ноутбуках с процессорами Intel и AMD..HP Notebook Fan Control in HWi. NFO3. 2 (ROUND 2 - AUTO FAN CONTROL CONFIG) ! Since I have received a lot of feedback on the Manual Fan Control I implemented on certain Elite. Book series (as discussed here: http: //forum. Automatic fan control tables as well, I have decided to implement this too. The original Fan Control allowed to change the controller to Manual Control state and set the fan speed to any value. This is the 2nd round of fan control which allows to modify the LUT (Look Up Table) which is activated when the controller is in automatic mode. Supported notebook models remain the same as previously (those which contain the SMSC EMC2. SMSC EMC2. 11. 3 controllers). To activate this feature use the same method as disclosed in the previous thread. Now an additional Lookup Table is displayed. To access this table, the controller needs to be switched to manual mode. The LUT consists of 8 different levels of fan control and each level is activated based on the value of any of the 4 displayed temperature thresholds (if any of these temperatures reaches the threshold value defined, the specified fan RPM value is activated). On some models (like the 8. Temp. 3 is monitored and available to be changed. On some others, the External temperatures are included in the table as well. Note, that on several models, the Temp. Celsius), but a PWM duty cycle instead which is a value supplied to the fan controller circuit. For example on 8. PWM_IN pin, on 8. Pushed Temperature 1. This value doesn't have a real correspondence to a fixed temperature value. Anyway, it's possible to modify this value (probably best would be some kind of guessing based on system observation).
You can convert the PWM duty cycle into % by: ( value/1. If you make any changes to the LUT, pressing the "Apply and Save" button stores the values into the fan controller circuitry and switches to Automatic mode to activate them (the controller needs to be in the Automatic mode in order to use the LUT values). These settings are then remembered in the registry as well, so when you run HWi. NFO3. 2 again and open Sensors, the values set will be loaded into the chip. This means, that to have your custom settings always active (after a reboot), you should autorun HWi. NFO3. 2 with Sensors (because the fan controller is configured by BIOS). I want to know how do I get HP Coolsense working again? http://forum.techinferno.com/hwinfo32-64-discussion/59-hp-notebook-fan-control-hwinfo32.html. HP Notebook Fan Control in HWINFO32 (программа подходит для некоторых Smart Fan и Fan Control (программы позволяют контролировать работу. This has the advantage that the original settings are always restored during boot in case the user makes a mistake. If you wish to clear the custom LUT settings, press the "Clear Preferences" button in HWi. NFO3. 2 / Configure. Sample screenshot (HP 8. Sample explanation: Rule 4: If the PWM_IN Duty cycle reaches 4. RPM. Rule 5: If the PWM_IN Duty cycle reaches 6. RPM. BE CAREFUL WHEN CHANGING ANY SETTINGS AND BE SURE YOU KNOW WHAT YOU ARE DOING ! YOU ARE RESPONSIBLE FOR ANY POTENTIAL DAMAGE ! Download the latest HWi. NFO3. 2 release which supports this feature: LINK REMOVED DUE TO NBR FORUM RULESPlease submit your feedback if/how this feature works ! Update: HWi. NFO3. Fan Minimum Drive setting (the minimum fan speed in %, a value below this threshold is considered by the fan controller as invalid and can't be used).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2016
Categories |